Caterpillar D6 Dozer Turbocharger Guide: C9 & C9.3 Engine Applications by Series
This Caterpillar D6 dozer turbocharger guide covers the turbos on D6 machines built with the C9 and C9.3 engines: what each engine family carries, how to identify the exact unit on your machine, how these turbos fail in dozer work and how to get the right replacement. The D6 name has stayed the same across many series, but the engine and turbo under the hood have changed, so the part number on the turbo’s tag is the only reliable starting point.
PT Turbo has been rebuilding turbochargers in San Bernardino, California since 1978, more than 45 years. This guide is for the mechanic or owner who has to keep a dozer pushing dirt, not for a parts counter guessing from the model name.
Identify the Engine Before You Order a Turbo
Not every D6 carries a C9-family engine. Cat has used different engines across D6 series, and across emissions tiers within a series, so “D6” alone does not tell you which turbo is bolted on. Start at the engine information plate. It gives the engine model and the serial number prefix, and those are what Cat and your parts supplier use to pin down the configuration.
Then go to the turbo itself. Caterpillar does not make its own turbochargers; Garrett and BorgWarner supply them. On a BorgWarner unit the nameplate sits on the compressor housing and carries the BorgWarner part number, the serial number and, on factory-fitted turbos, Caterpillar’s own part number. BorgWarner part numbers are six digits on older S-series units and eleven on newer ones.
- Clean the tag before you read it. Years of heat, oil mist and dust make digits easy to misread.
- Do not order by the casting number on a housing. One casting serves many turbos, so it narrows the search at best.
- Photograph the tag, the turbine inlet flange and the oil feed and drain connections before the turbo comes off.
- If the tag is missing or unreadable, the engine serial prefix and the Cat part number are the next path. Call the shop at (909) 824-1020 with both.
C9 and C9.3 Turbochargers: What Each Engine Family Carries
Both the C9 and the C9.3 run a single turbocharger in machine service. Neither uses series turbos, which keeps the system simpler than the C13 and C15 ACERT truck engines; our Caterpillar C15 turbocharger guide covers that two-turbo layout.
On most C9 ratings the turbo is a BorgWarner S310-family unit. The S310 frame is also listed for the Cat C10 and C12, which is exactly why the frame name is not enough to order from. The letters and digits after “S310” mark different versions, and versions built for different ratings are not interchangeable just because the frame matches.
Some C9 machine ratings carry a smaller BorgWarner S200AG or S200ACG instead, and the S200AG048 is one of the numbers listed for the C9. Our BorgWarner S200 turbochargers page lists the S200-frame parts. The variable-vane C9 turbo is listed for the 2007-on truck engines. If you run C9-powered trucks and machines in the same fleet, never assume a turbo from one fits the other.
| Engine | Turbo layout | Turbo families listed | How to choose the replacement |
|---|---|---|---|
| C9, most ratings | Single turbo | BorgWarner S310 family (S310G080, S310CG080, S310G116, S310G122) | Match the full BorgWarner or Cat number on the tag, suffix included |
| C9, some machine ratings | Single turbo | BorgWarner S200AG / S200ACG (S200AG048 listed for the C9) | Match the tag; the S200 and S310 are different frames |
| C9 truck engines, 2007 on | Single turbo | Variable-vane turbo | Not a reference for a dozer engine; match your own tag |
| C9.3 | Single turbo, never series | Identify by tag number | Read the tag and send us the number |
Turbos we list for the S200
Listings for the turbo models named in this guide that can be ordered online today. Several part numbers can fit one engine by year and rating, so match the number on your turbo’s tag, or call (909) 824-1020 and we will match it for you.
How Turbos Fail in Dozer Work

A dozer spends its life in its own dust cloud, under heavy load, with long idle periods mixed in. Each of those conditions attacks the turbocharger in a different way, and the damage pattern on the wheels usually tells you which one did it.
Dust Ingestion
Dust that gets past the air cleaner shows up as pitting on the compressor inlet blades. The pipe between the air cleaner and the turbo is under suction, so a cracked hose, loose clamp or split elbow there does not leak boost. It pulls unfiltered dirt straight into the compressor. Replace the air filter when the restriction indicator says so, and treat every inlet-side joint as critical.
Oil Supply Problems
Garrett states that more than 90 percent of turbo failures come from oil starvation or oil contamination. Starvation comes from hard acceleration from cold, blocked or leaking oil pipes, and a turbo started without priming. Contamination comes from carbon, engine wear debris, dirt let in during servicing, a faulty filter bypass or degraded oil, and it shows as abrasive wear on the bearings.
Change oil on Cat’s schedule, or its severe-service schedule when the machine works in heavy dust or idles for long stretches. Shutting down hot after a hard push cooks oil in the center housing and leaves carbon behind; idle down for the time Cat gives in the operation manual for your machine.
Impact and Exhaust-Side Damage
Bent or chipped compressor blades are impact damage from something solid in the intake. Debris damage on a turbine wheel shows on the inlet edges and comes from the engine side. A wheel with blade damage is replaced, never rebalanced and reused. A cracked manifold or leaking gasket ahead of the turbine lets exhaust escape before it does work: low boost, slow response and higher exhaust temperature.
| Symptom | What it usually points to | Check first |
|---|---|---|
| Black or dark gray smoke under load, low power | Too little air (low boost) | Air filter restriction, inlet and charge-air leaks, exhaust leaks before the turbine |
| Blue-gray smoke | Oil being burned | Crankcase pressure, breather, air filter, oil level and turbo drain before the seals |
| Whine or siren noise | Exhaust leak before the turbine, boost leak, wheel rubbing or foreign object | Every joint first, then wheel contact |
| Oil pooled in the charge piping | Oil passing the compressor-side seal | Air filter restriction, drain flow, crankcase pressure (a light film is normal crankcase vapor) |
| Oil at the turbine end after long idle | Low exhaust flow at idle | Often clears under load; check the drain |
| Wheel touches the housing when rocked | Journal bearing wear | Turbo comes off; find the cause before fitting the next one |
Diagnosing a D6 Turbo Before You Pull It

A turbo is often the victim, not the cause. Rule out the cheaper problems first, because a new or rebuilt turbo fitted to an engine with the same fault will fail the same way.
- Read the machine’s codes. Cat machines report through Cat’s own diagnostic codes, not OBD-II P-codes, so there is no P0299 on a dozer. Read active and logged codes with Cat’s service software and look at the boost readings it shows.
- Check shaft play correctly. Some side-to-side rock at the wheel is normal on a journal-bearing turbo with no oil pressure. In-and-out play you can feel, or a wheel that touches its housing, condemns it. For end play, use the maker’s limit for that unit.
- Measure crankcase pressure. There is no universal healthy figure. Test the way your service manual describes and compare with its limit. High crankcase pressure pushes back on the turbo drain and shows up as oil at both ends.
- Inspect the drain. Oil leaves the turbo by gravity. The drain must run downhill and enter the crankcase above the oil level. A kinked or restricted drain backs oil up past the seals; it does not starve the bearings, which is a feed-side fault.
- Use oil analysis as a trend. Turbo journal bearings are bronze, so copper is the bearing wear metal to watch. Compare against your own baseline and the lab’s limits. Turbine wheels are a nickel alloy, so rising iron is not coming from the turbine wheel.
- Check the aftertreatment if fitted. On an engine with a diesel particulate filter, the filter sits after the turbo. A loaded filter raises exhaust backpressure, so check it when power is down, and let an active regeneration finish as Cat advises.
Replacement Options and Installation
With the tag number in hand you have three routes. Search the store by the number on your tag for a new unit; current pricing is on the product page, or call (909) 824-1020. Check our remanufactured turbochargers by the same number; whether a matching reman is available depends on core supply.
The third route is our in-house turbocharger rebuild service, often the practical answer for machine turbos. Every turbo we rebuild is VSR balanced and gets a final quality inspection: leak test, visual inspection and an actuator or wastegate function check. Most rebuilds ship in 3 days or less, and the price is confirmed after inspection, before work starts. Our turbo rebuild price list shows rebuild prices by turbo.
Rebuilds and remanufactured units carry a 12-month warranty with unlimited mileage. Core returns on remanufactured turbos are due within 30 days, with return shipping paid by the customer; if you need longer, call ahead and the shop can usually work with you. Fleets running several D6 machines can arrange priority and rush turnaround, or have us stock their common cores, by phone through our contact page.
Installation Checklist
- Find and fix what killed the old turbo before the new one goes on.
- Fit a new oil feed line after any bearing failure or coked oil. Do not flush and reuse the old one.
- Use new gaskets, and no sealant on the oil inlet or drain gaskets.
- If the compressor wheel shed metal, replace the charge air cooler. Metal in the fins cannot be reliably flushed out. Clean or replace the charge piping too.
- Clean the inlet ducting from the air cleaner to the turbo and use new clamps.
- Fill the oil inlet with clean engine oil and turn the wheel by hand.
- Crank 10 to 15 seconds without starting, keeping the engine from firing by Cat’s procedure, then start and idle 3 to 4 minutes while you check for oil, exhaust and air leaks (Garrett’s installation steps).
There is no break-in period. Once the first start checks out, the machine goes back to normal work.
Frequently Asked Questions
Does every Caterpillar D6 dozer use a C9 or C9.3 engine?
No. Cat has used different engines across D6 series and emissions tiers, so the model name does not tell you the engine or the turbo. Read the engine model and serial prefix from the engine information plate, then order by the part number on the turbo’s tag.
Will a turbo from a C9 truck engine fit my dozer’s C9?
Do not assume it will. Most C9 machine ratings are listed with BorgWarner S310-family turbos and some with an S200AG or S200ACG, while the 2007-on C9 truck engines are listed with a variable-vane turbo. Match the full number on your own turbo’s tag, suffix included.
Can I rebuild my D6 turbo instead of buying a new one?
In most cases, yes, as long as the housings are serviceable. Every turbo we rebuild in-house is VSR balanced and gets a final quality inspection, and most rebuilds ship in 3 days or less. The price is confirmed after inspection, before any work starts, so call (909) 824-1020 with your tag number.
Need a Turbocharger?
PT Turbo has rebuilt and sold turbochargers since 1978. We stock remanufactured units for Cummins, Duramax, Power Stroke, Detroit Diesel, and more — backed by a 12-month unlimited mileage warranty. Units in stock at our shop in San Bernardino, CA ship the same day when ordered before 2 PM Pacific, Monday through Friday.
📞 (909) 824-1020 · 346 S I St. #3, San Bernardino, CA 92410 · info@ptturbo.com



