Skip to content
PT Turbo logo
(909) 824-1020 Get a Quote

Case IH Magnum Tractor Turbocharger Guide: FPT & Cummins Engine Applications

This Case IH Magnum tractor turbocharger guide rests on one rule: the number on the turbo tag picks the part, not the badge on the hood. The word “Magnum” also appears on turbo listings for a road truck, and one Holset family comes in many versions for different engines. A search by tractor model alone can hand you the wrong turbo.

PT Turbo is a family-owned shop in San Bernardino, California, and has been rebuilding turbochargers since 1978. Below you will find which turbos our catalog data ties to the Magnum, where that data stops, how these turbos fail under field load, and how to fit a replacement so it has the best chance of a long service life.

Read the Engine Plate and the Turbo Tag First

Start with the engine data plate. It names the engine maker and model. On a Cummins engine it also carries the CPL, which identifies the engine, not the turbo. Then go to the turbo itself. On a Holset the data plate sits on the compressor housing.

A Holset tag shows two numbers in separate fields:

  • The Holset assembly number: seven digits plus a letter suffix, for example 3787091H.
  • The engine maker’s own part number.

Either number works as a search key. Neither describes the turbo’s size or features, so look it up rather than trying to decode it.

A Garrett part number reads six digits, a dash, four digits and usually an S. The first digit after the dash gives the sales channel: 0 for original equipment, 5 for new aftermarket and 9 for remanufactured. Nameplate position varies by plant, so check every housing face before you decide the tag is missing.

Ignore the numbers cast into the housings. One casting serves many different turbos, so a casting number only narrows the search. Wheel sizes and housing A/R confirm the match. If the tag is gone, call (909) 824-1020 with the engine plate details and clear photos of the turbo.

FPT Cursor 9 Magnums: The Holset HX52W and Later Garrett Units

Earlier Case IH Magnum tractors with the FPT Cursor 9 are listed with a Holset HX52W turbocharger. The W marks a wastegated turbo. A valve lets part of the exhaust bypass the turbine wheel so boost stops climbing at its setting. It is a fixed geometry turbo, with no sliding nozzle to stick.

One listing in our catalog names the tractor directly: Holset HX52W 3787091H. Its application row reads “Case-New Holland (CNH) Magnum Tractor (Off-Highway) 8.7L 284-380HP”. That row gives a displacement and a power range, not an engine family or model years. Compare 3787091H with the tag on your turbo instead of ordering by horsepower. Current pricing is on the product page, reached through the HX52W model page, or call (909) 824-1020.

The HX52 family is not a tractor-only turbo. It is listed for the Volvo D12, the Volvo and Mack 11 liter, Scania and Iveco Cursor 9 engines, each version with its own assembly numbers and housings. Two HX52W units can look alike on the bench and still not interchange.

The HX55W, and the “Magnum” That Is a Truck

The Holset HX55W is listed mainly for FPT Cursor combines, not tractors. We have no source for fitting a combine’s HX55W to a Magnum. Treat that swap as unproven.

Watch the name itself as well. Two Holset HX55 listings carry “Magnum” next to a Volvo D12D engine. That is the Renault Magnum road truck, and those turbos are not Case IH tractor parts.

Later Cursor 9 Tractor Engines With a Garrett

Tier 4B Cursor 9 tractor engines from 2020 on are listed with an electrically actuated Garrett GTC4088V. In Garrett names, the V marks a variable nozzle turbine. None of our listings ties this turbo to a Magnum by name, so match a tractor from that era by the Garrett number on its nameplate.

The electric actuator is calibrated to its own turbo when Garrett builds it. Never push the actuator arm by hand, because the gears are self-locking and break. To check vane travel, sweep the actuator with the service tool, or unbolt it and move the vane lever instead. For background on how these turbos vary exhaust flow, see this overview of variable-geometry turbochargers.

Turbo What our data lists it for Boost control What to check
Holset HX52W Earlier Magnum tractors with the FPT Cursor 9; listing 3787091H names “Magnum Tractor (Off-Highway) 8.7L 284-380HP” Wastegate Assembly number or engine maker’s number on your tag
Holset HX55W Mainly FPT Cursor combines Wastegate No source for use on a Magnum tractor
Holset HX55 rows marked “Magnum” Renault Magnum road truck, Volvo D12D Not a tractor part Skip these in a tractor search
Garrett GTC4088V Tier 4B Cursor 9 tractor engines, 2020 on Variable nozzle, electric actuator Garrett number on the nameplate; actuator stays with its turbo

Turbos we list for the HX52W, HX55W and HX55

Listings for the turbo models named in this guide that can be ordered online today. Several part numbers can fit one engine by year and rating, so match the number on your turbo’s tag, or call (909) 824-1020 and we will match it for you.

All HX52W listings · All HX55W listings · All HX55 listings

Cummins Engines: Match the Holset by Its Number

Our catalog has no listing that names a Cummins engine in a Case IH Magnum. For that reason we will not give you a Cummins part number for the tractor. If your engine plate reads Cummins, the tag on the turbo is your starting point.

Cummins owns the Holset brand. It bought Holset in 1973 and has run it as Cummins Turbo Technologies since 2006. The Cummins engines in our data carry Holset turbos, so read the tag exactly as described above.

For Cummins 8.3L engines in general, our data lists these Holset models:

That is engine fitment, not tractor fitment. Confirm it against your own tag.

The WH1E belongs to mechanical-era engines, so there are no generic P-codes to read. On any tractor, OBD-II codes such as P0299 are a road-vehicle standard. Read the machine’s own fault codes with its service tool, and on older engines use a boost gauge, the exhaust smoke and the turbo itself.

How Magnum Turbos Fail Under Field Load

Dust pitting on the compressor blade inlet edges of a Holset HX52W
Dust entering upstream of the turbo can pit the compressor blade inlet edges.

Tractor turbos run long hours near full load, often in dust. Garrett states that more than 90 percent of turbo failures come from oil starvation or oil contamination, with foreign objects the third main cause.

Oil starvation comes from three things:

  • Low oil pressure.
  • A blocked or leaking feed line.
  • Hard throttle from cold, or a first start before the turbo was primed.

Shutting down hot does something different: it cokes oil in the center housing. Contamination comes from carbon, engine wear debris, dirt let in during service, a faulty filter bypass and degraded oil. In dust or heavy idling, follow the engine maker’s severe-service oil schedule.

Dust shows as pitting on the inlet edges of the compressor blades. Replace the air filter when the restriction indicator calls for it. The pipe between the filter and the turbo is under suction, so a crack there cannot leak boost, but it pulls unfiltered dirt straight into the wheel.

Drain problems look like seal failures. The drain is a gravity return that must run downhill and enter the pan above the oil level. A kinked or crushed drain backs oil up and leaks it at both ends of the turbo.

A light oil film in the intake is normal crankcase vapor. Pooled oil is not normal, but check the drain and the breather before you blame the turbo.

What you see Where to look first What it points to
Black or dark gray smoke, low power under load Air filter restriction, charge-air leaks, exhaust leaks before the turbine Low boost; a wastegate that does not seat or a sticking nozzle also cuts boost
Blue-gray smoke, pooled oil in the intake Oil drain, crankcase breather, air filter, oil level Check these before condemning the seals
Oil leaking at both ends of the turbo Drain line kinked, crushed or running uphill Restricted drain backing oil past the seal rings
Overboost Wastegate actuator and linkage; nozzle stuck closed on a variable turbo A leaking diaphragm on a boost-opened actuator opens the gate late
Whine or siren under load Every joint: exhaust leaks before the turbine, boost leaks Suspect wheel rub only after leaks are ruled out
Bent or chipped blades Intake ducting, loose hardware, upstream exhaust parts Impact damage; the wheel is replaced, never rebalanced and reused

An exhaust leak at the manifold or the turbine flange lets gas escape before it can drive the wheel. The result is low boost, slow spool and higher exhaust temperature, with a healthy turbo taking the blame.

When you check shaft play, some side-to-side rock is normal on a journal bearing turbo. In-and-out play you can feel, or a wheel that touches its housing, condemns it.

Fitting a Replacement or Sending Yours for Rebuild

Clean oil being added to the oil inlet of an HX52W during installation on a Cursor 9 Magnum
Prime the oil inlet with clean engine oil before following the engine maker’s first-start procedure.

Fix the cause before the new turbo goes on. Then follow the maker’s first-start steps:

  • Fit a new oil feed line after a bearing failure or coked oil. Do not flush and reuse the old one.
  • Route the drain within about 15 to 20 degrees of straight down. Use no sealant on the oil inlet or drain gaskets.
  • If the compressor wheel shed metal and the engine has a charge air cooler, replace the cooler. MAHLE notes that metal in the fins cannot be flushed out reliably. Inspect the charge piping too.
  • Fill the oil inlet with clean engine oil and turn the wheel by hand.
  • Disable fueling by the engine maker’s procedure. Crank 10 to 15 seconds without starting, then start and idle 3 to 4 minutes while you check for oil, exhaust and air leaks before loading the tractor.

After heavy drawbar work, let the engine idle before shutdown. Holset’s failure-diagnosis guidance calls for two to three minutes; use your engine maker’s figure where the manual gives one.

If your turbo is rebuildable, our in-house turbo rebuild service handles Holset and Garrett units:

  • Every turbo we rebuild is VSR (Vibration Sorting Rig) balanced.
  • Each one gets a final inspection: a leak test, a visual inspection and an actuator or wastegate function check.
  • Most rebuilds ship in 3 days or less.
  • The price is confirmed after inspection and before work starts. See the turbo rebuild price list for current figures.
  • The warranty runs 12 months with unlimited mileage.

To find a replacement, search our store by the number on your tag. If nothing matches, contact PT Turbo and we can quote a rebuild of your own unit by phone.

Frequently Asked Questions

Which turbocharger does my Case IH Magnum use?

It depends on the engine, and the tag on the turbo has the final word. Earlier Magnum tractors with the FPT Cursor 9 are listed with a Holset HX52W. One listing in our catalog, 3787091H, names “Magnum Tractor (Off-Highway) 8.7L 284-380HP”. Tier 4B Cursor 9 tractor engines from 2020 on are listed with an electrically actuated Garrett GTC4088V. Match the number on your tag before ordering.

Can I fit the HX55W from a Case IH combine to my Magnum?

We have no source that supports that swap. The HX55W is listed mainly for FPT Cursor combines, while the HX52W is the turbo listed for earlier Cursor 9 Magnum tractors. Different turbos can differ in housings, flanges and wastegate setup, so order by the number on your tractor’s tag.

Can PT Turbo rebuild my Magnum turbocharger?

Yes. Call (909) 824-1020 with the tag number, or send the turbo in. Every unit we rebuild in-house is VSR balanced and inspected before it ships, most rebuilds ship in 3 days or less, and the price is confirmed after inspection. For a Garrett with an electric actuator, call before shipping and send the turbo complete with its actuator.

Need This Turbo Rebuilt?

About the author

Niles Nimmo has worked on turbochargers for 19 years. PT Turbo has rebuilt and supplied turbochargers in San Bernardino, California since 1978. More about Niles and all of his guides.

Need a Turbocharger?

PT Turbo has rebuilt and sold turbochargers since 1978. We stock remanufactured units for Cummins, Duramax, Power Stroke, Detroit Diesel, and more — backed by a 12-month unlimited mileage warranty. Units in stock at our shop in San Bernardino, CA ship the same day when ordered before 2 PM Pacific, Monday through Friday.

📞 (909) 824-1020  ·  346 S I St. #3, San Bernardino, CA 92410  ·  info@ptturbo.com

Call Now Get a Quote