Perkins 1104 Turbocharger Guide: Massey Ferguson, JCB & Telehandler Applications
Use this Perkins 1104 turbocharger guide when a tractor, telehandler or backhoe on your yard loses power, smokes or starts pushing oil and you need the right turbo the first time. The 1104 is the four-cylinder engine in Perkins’ 1100 series. It went into a long list of off-highway machines, including Massey Ferguson tractors and JCB equipment. Because it is in so many machines, the machine name alone will not tell you which turbo you need.
PT Turbo is family-owned and has rebuilt turbochargers since 1978, more than 45 years, in San Bernardino, California. This guide covers how to identify the turbo on your 1104, how these turbos fail in farm and materials-handling work, how to fit one so it survives its first start, and how to choose between a rebuild and a replacement.
Where the Perkins 1104 Shows Up and Why Its Turbos Differ
The 1104 is used in agricultural tractors, telehandlers, backhoe loaders, compact construction machines and generator sets. Massey Ferguson and JCB both built machines around it, and so did other equipment makers. Many newer machines from both brands use engines from other makers, so read the engine plate before you assume you have a Perkins.
“1104” is the name of an engine family, not one engine. Perkins built it in naturally aspirated, turbocharged and turbocharged-aftercooled forms, with mechanical or electronic fuel systems, across several generations and emissions levels. The suffix on the engine plate tells these builds apart: a T marks a turbocharged engine and TA a turbocharged, aftercooled one.
The machine maker then adds its own changes. A tractor, a telehandler and a backhoe each mount the engine differently, so turbos built on the same core can differ in:
- Compressor outlet direction and turbine housing clocking, set to suit how the engine sits in the frame
- Oil feed and drain positions, which must line up with the machine’s own lines
- Wastegate details, on units that have a wastegate
- Housing and wheel sizes matched to the engine’s rating and emissions level
Two machines with the same engine name can therefore carry turbos with different part numbers, and one will not bolt in where the other came off.
Identify the Turbo by Its Tag, Not the Machine
The data plate on the turbo is the only reliable starting point. It shows the turbo maker’s part number and serial number, and on factory-fitted units it usually shows the engine maker’s number as well. The layout depends on who built the unit:
- Garrett: six digits, a dash and four digits, usually ending in S. The first digit after the dash shows the sales channel: 0 for original equipment, 5 for new aftermarket, 9 for remanufactured. Where the nameplate sits varies by plant.
- Holset: a seven-digit assembly number with a letter suffix, with the engine maker’s (customer) number in a separate field on the compressor housing plate.
- BorgWarner: a six- or eleven-digit part number plus the serial number, on the compressor housing.
Do not order by the casting number on a housing. One casting is used on many turbos, so it only narrows the search. If the plate has been painted over or burned off, send us the engine serial number from the Perkins engine plate, the machine make and model, and clear photos of both housings and the oil connections.
Once you have the number, search for it in our turbo catalog. If the number on your plate has been superseded, meaning a newer number has replaced it, parts lists will show the newer number. If you cannot find your number, call (909) 824-1020.
How 1104 Turbos Fail in Farm and Yard Work

Turbos on tractors and telehandlers have a harder life than most on-road units. They deal with dust, long idle periods between lifts, cold starts followed straight away by heavy load, and hot shutdowns at the end of a shift. Each of these damages the turbo in its own way.
Dust
The pipe between the air filter and the turbo is under suction. A cracked hose or loose clamp there cannot leak boost. Instead, it pulls unfiltered dirt into the compressor, which leaves pitting on the leading edges of the blades. Replace the filter when the restriction indicator calls for it, and inspect that pipe every time the filter is out. Bent or chipped blades are impact damage from a solid object, not dust.
Oil supply and oil quality
Garrett states that more than 90 percent of turbo failures come from oil starvation or oil contamination. Starvation comes from blocked or leaking oil lines, a turbo fitted without priming, or hard throttle on a cold engine before oil reaches the bearings. Carbon is the most common contaminant. Change oil and filters on the maker’s schedule, or on its severe-service schedule if the machine works in dust or idles a lot.
Heat and idling
Shutting down hot after a hard pull bakes the oil left in the center housing into carbon, which wears the bearings and sticks the seal rings. Idle the engine for the cool-down time your engine maker gives before shutdown. Long idling causes a different problem. With little exhaust flow, oil can show at the turbine end as blue-gray smoke, and it usually clears once the machine works under load.
Drain and crankcase pressure
The oil drain works by gravity. It must run downhill, within about 15 to 20 degrees of straight down, and enter the sump above the oil level. A kinked or blocked drain, or high crankcase pressure from a worn engine, backs oil up in the center housing and pushes it out at both ends. Compare crankcase pressure with the figure in the service manual for your engine, because no single figure applies to all engines.
| Symptom | What it usually points to | Check first |
|---|---|---|
| Black or dark gray smoke, low power, slow response | Low boost: restricted filter, charge-air leak, exhaust leak before the turbine, wastegate not seating, worn turbo | Restriction indicator, hoses and clamps, manifold gasket, then the turbo |
| Blue-gray smoke | Oil past the turbine end, or engine wear | Idle history, drain line, crankcase pressure, then shaft play |
| Oil pooled in the charge-air piping | Oil past the compressor end | Air filter, drain, breather, oil level (a light film from crankcase vapor can be normal) |
| Whine or siren under load | Exhaust or boost leak, or a wheel rubbing | Every joint first, then wheel contact |
| Wheel touches the housing when rocked | Journal bearing failure | Remove the turbo and find the oil cause |
| Oil on the outside of the center housing | Gasket or oil line leak, not the seals | Feed and drain fittings and gaskets |
| White smoke | Coolant, or unburned fuel on a cold engine | Coolant level and cold-start fueling, not the turbo |
On shaft play: some side-to-side rock at the wheel is normal on a journal bearing turbo. Condemn the turbo for in-and-out play you can feel, for wheel contact with the housing, or for play beyond the maker’s limit. Mechanical 1104 builds set no fault codes. Electronic builds report through the engine maker’s own diagnostics, not road-vehicle OBD-II codes.
Fitting a Replacement Turbo to an 1104

If you fit a new turbo without fixing what destroyed the old one, it will fail the same way. Before the replacement goes on:
- Find the cause: oil supply, drain routing, air filter and intake piping, crankcase pressure.
- Fit a new oil feed line rather than reusing the old one after a bearing failure or coked oil, and make sure the drain path is clear.
- Use new oil inlet and drain gaskets, with no sealant.
- On an aftercooled engine, replace the charge air cooler if the old compressor wheel shed metal. Metal trapped in the fins cannot be flushed out reliably. Clean or replace the charge piping as well.
- Fit charge-air boots clean and dry, with the clamps behind the bead.
For the first start, fill the oil inlet with clean engine oil and turn the wheel by hand. Crank for 10 to 15 seconds while keeping the engine from starting, using the method Perkins gives for your build. Then start it and idle for 3 to 4 minutes while you check for oil, exhaust and air leaks. These are Garrett’s installation steps. Never run the engine with the turbo’s oil feed capped.
The turbo needs no break-in after that: no hour schedule, no reduced-boost period and no early oil change. As on any working day, avoid full load until the engine is warm.
Rebuild, Remanufactured or New for a Perkins 1104
| Option | Strengths | Watch for |
|---|---|---|
| Rebuild your own turbo | Keeps the exact housings, clocking and connections your machine came with; VSR balanced and inspected in-house | Needs a rebuildable core; damaged wheels or housings are replaced |
| Remanufactured exchange | Tested, flow-tested unit; less downtime | Availability depends on core supply for your number; core return within 30 days |
| New | Brand-new unit with the maker’s warranty | Availability and pricing vary by part number |
For most 1104 machines, rebuilding the turbo you already have gives the surest fit, because the machine maker’s housing positions and connections stay as they were. Our turbo rebuild service does the work in-house. Every unit is balanced on a VSR (Vibration Sorting Rig) and gets a final quality inspection: a leak test, a visual inspection and a wastegate or actuator function check. Each one comes back with inspection notes.
Most rebuilds ship in 3 days or less. We confirm the price after inspection, before any work starts, and our turbo rebuild price list shows rebuild prices by turbo. If the machine cannot sit idle that long, search your tag number in our remanufactured turbochargers. The units we sell are tested, flow-tested and calibrated before they ship. For new units, current pricing is on the product page, or call (909) 824-1020.
If you run several 1104 machines, a rental yard or a dealer shop, we can arrange priority or rush turnaround and stock the cores your fleet uses most. Set that up by phone. If your yard also runs Cummins or Cat engines, our Cummins QSB turbocharger guide and Caterpillar C9 turbocharger guide cover those engines.
Frequently Asked Questions
Will a turbo from a Massey Ferguson with a Perkins 1104 fit a JCB telehandler with the same engine?
Only if the part numbers on the two turbo tags match, or if the turbo maker lists one as a replacement for the other. Machine makers set outlet direction, housing clocking, oil line positions and wastegate details to suit their own installation. The same engine name can carry turbos that will not swap, so match the tag number, not the engine name.
The tag on my 1104 turbo is gone. Can it still be identified?
In many cases, yes. Send the engine serial number from the Perkins engine plate, the machine make and model, and photos of both housings, the flanges and the oil connections. Casting numbers help narrow the search and wheel and housing details confirm the match, but never order by a casting number alone.
How long does a turbo rebuild take for an 1104?
Most rebuilds ship in 3 days or less. The price is confirmed after inspection and before work starts. If the machine cannot wait, a remanufactured exchange unit may be available, depending on core supply for your part number.
Need a Turbocharger?
PT Turbo has rebuilt and sold turbochargers since 1978. We stock remanufactured units for Cummins, Duramax, Power Stroke, Detroit Diesel, and more โ backed by a 12-month unlimited mileage warranty. Units in stock at our shop in San Bernardino, CA ship the same day when ordered before 2 PM Pacific, Monday through Friday.
๐ (909) 824-1020 ยท 346 S I St. #3, San Bernardino, CA 92410 ยท info@ptturbo.com



